Gun CodeModelNotes
G1
Govt. Model - Wood and PolymerThe Colt Government model is known by many names and is copied by many other manufacturers.
It is a Semi Automatic pistol with a single stack magazine, made since 1911. Available primarily in .45 Caliber it is also available in .38 super, 40 S&W, 9mm Para, .22LR and probably many more.

-As a general rule our panel style grips fit all of the clones made by the other manufacturers.

-Grip screw hole spacing is 3 1/16"

-You use the stock screws to install our grips, We also sell replacement screws for the 1911. They are available slotted or hex head in Black or satin SS finish. Look up part numbers below.

-Grip screws should be torqued to 12 inch lbs. Blue loctite is suggested on the threads. A quality correct fitting 3/32" hex / Allen or slot driver is a must!

-Taurus 1911 pistol. Stock grip screw heads are too large. Screws must be exchanged for standard Colt dimensions. Grips must be relieved for extended safety lever to assure full travel. Ambidextrous safety requires ambi cut.

Hogue 1911 grips fit the following Colt models:

-1991 A1, Gold Cup, Delta Elite, Combat Commander, MARK IV, and Full size series 70 and 80.

Some other makes that the grip fits are:

- Will fit Kimber Classic and full size 1911, Kimber pro carry compact***this gun has a compact barrel but the grip/magazine frame is full size***.
- Will fit Kimber Pro CDP II
- Will fit Wilson Combat full size 1911.
-Will fit the Springfield Armory 1911
-Will fit Spingfield Champion
-Will fit Norinco 1911-A1
-Will fit Sig Sauer GSR 1911
-Rubber grips will fit Beeman P-1 air pistol NOT wood grips.
-Will fit Para Ordnance LTC #PCX745E...
-Will fit Para Ordnance LTC #PCX745R...
-Will fit Para Ordnance LTC #PCX745S...
-Will fit Para Ordnance 1911 SSP #PX745E...
-Will fit Para Ordnance Tac-S #DCX745E...
-Will fit Para Ordnance Black Witch SSP #DX745E...
-Will fit Para Ordnance LDA SSP #DX745S...
-Will fit Para Ordnance Covert Black Limited #TX745E...
-Will fit Para Ordnance Limited #TX745S...
-Will fit Colt 1911 Govt. dedicated 22LR.

-There are many many more models that our grips work on.

Hogue 45 Grips WILL NOT fit the following:

-will not fit Colt officers, 1991 Compact or the Springfield Armory Compact, "C" series From Para-Ordnance. You must use the #43000 for the compacts
-Will not fit .380 series-ie:Mustang
-will NOT FIT THE COLT PONY
-Will Not Fit The Llama .45
-Wraparound wood and rubber grips will not fit auto ordnance. They will leave 1/2" gap in front where finger grooves are.
-Will not fit Para-Ordnance Covert Black Carry #CWX645B...
-Will not fit Para-Ordnance Carry #CWX645S...
-Will not fit Para-Ordnance CCO Companion, Carry Option #CWX745S...
-Will not fit Para-Ordnance CCW #CCWX745S...
-Will not fit Para-Ordnance OPS #PCWX745S...
-Will not fit Para-Ordnance Black Witch Companion #CX745S...
-Will not fit Browning 1911 dedicated 22LR
-Will not fit Coonan 357 magnum models

-Our grips will not fit the Sig 1911-22 without the customer modifying the ambi safety pocket. The ambi safety on the Sig 1911-22 is much bigger than the standard ambi safety. The relief for the 1911-22 must be taller, deeper and lower than standard. Also the stock grip panels for the Sig 1911-22 are taller than our grip panels. We cannot add material to our grip panels as it will interfere with aftermarket ambi-safeties

-Extreme Aluminum and G-10 1911 panels come with the ambi cut standard.

-Hogue Extreme grips come in both thick and thin models. The thin grips require the use of short bushings and screws available through Brownell's and other gun smith parts sources. The thick grips use standard length bushings and screws.

-Our grips may not clear some extended slide release levers or the magazine release on left side. The customer may have to relieve the grip to fit.

-Checkered wood panels have double diamond style 20 LPI (lines per inch)checkering. The Finger Groove and Palm Swell models are Fully checkered and do not have the double diamond.

-Wood grips are not cut for an ambidexterous safey - need to specify if they need ambi-cut.

-The ambi cut comes standard on the wood wraparound grips with finger grooves and the palm swell models.

-Palm Swell version can be cut for S&A mag

-Springfield armory guns and a few other clones are a bit larger in the frame, our wraparound wood grips will not fit well. For the Springfield armory full size guns, the wood needs to be removed on the inside of the front of the grips where they meet at the frontstrap. This modification may work on other makes that our wraparound will not fit.


If you are unsure about your frame size, please measure your screw hole spacing and confer with a customer service representative at 1-800-438-4747 

Product CodePart nameDescriptionHelp callsPhoto
   
Notes:
 
No Calls See Picture
Hogue Inc. Copyright © 2024